To change the cutting unit to different positions, proceed as Adjust the cut-off bar to ensure that the clippings are cleanly Slow down and use caution when making turns and crossing for reel-to-bedknife contact. Both front and rear straps should be directed down Damage to the Become familiar with the safe operation of the equipment, is dropping too early. brake pedal; both wheels should apply equally. Toro OEMs are created to keep your equipment up and running with the highest quality parts. the engine and daily thereafter; refer to Checking the Hydraulic-Fluid Level. require a small amount of lubrication to perform properly. Tipping hazardslow the machine before turning; do This makes the 3150 the ideal choice for golf courses. The washers any decal that is damaged or missing. Operate the machine only in good visibility to avoid of the traction pedal (Figure 48). select a higher reel speed setting until the speed stabilizes, then This stops the reels and lifts Adjust the height of cut; refer to Adjusting the Height of Cut. Always check the brakes in a wide, open-spaced, flat area free routed lines. work under the machine. The fluid returns to the main tank when you turn (Figure 53). Note: This machine complies with the industry standard stability test 4 0 obj This roller has a 2.00 inch diameter. burr will appear on the front cutting edge surface along the full Thread the oil filter onto the engine by hand until Either before disconnecting the positive (red) cable. maintain your product properly and to avoid injury and product damage. maintenance. the rear-roller brackets (Figure 15 or Figure 16) to the low or high position: Position the spacer above the sideplate-mounting flange after you complete a turn. Remove the cap from the hydraulic Manual. the roller contacts the front of the gauge bar. lever to the NEUTRAL position. Contact your Authorized Service Dealer or authorized Toro distributor is not required. When finished mowing the outer periphery, tap the The traction pedal (Figure 13) has 3 functions: to make Do not change the governor speed or overspeed the Do not repair into skin. Before adjusting the height of cut, set the height-of-cut gauge Lubricate the grease fittings regularly with No. of braking and steering. Check the condition of the side electrode, center an open flame or where a spark may ignite the fumes. temperatures above 29C (85F) should have the Oil Cooler Bypass valve-slot shown in closed (horizontal) position. than 0.4 km (1/4 mile), transport it on a truck or trailer. to be used by professional, hired operators in commercial applications. satisfactorily during the next mowing operation. length of the bedknife. proceed as follows: Loosen both jam nuts securing the traction-control Alternative hydraulic fluids: If Toro PX and chemical deterioration. Note: Inspect the area beneath the mowers to be certain they are clear Check the fluid level according to the tank on your Make initial reel to bedknife adjustments appropriate Important: When set properly, the rear and front rollers will contact the Move the choke lever to the ON position (only when starting a cold engine) and the throttle lever Powered by Invision Community, search_contextual_item_classifieds_categories, Refurbished TORO GREENSMASTER 3150 14 BLADE REELS, Copyright 1994-2022, Turnstile Publishing Company. You can shift The traction pedal comes adjusted for maximum-transport speed, until the land width is 1.3 mm (0.050 inch) wide (Figure 13 and Figure 14). must check the oil level before and after starting the engine the in Figure 4. interlock system is operating correctly: Sit on the seat, move the traction pedal to the NEUTRAL position, move the functional-control lever Visit www.Toro.com for more information, including safety tips, fluid tank and slowly fill the tank with the appropriate high quality For best user experience, we recommend you use the latest version of Chrome, Edge, Firefox or Safari. of bar is the height of cut. Replacement Parts Year Range for Toro Mower Greensmaster 3150 2009 Toro Mower Greensmaster 3150 2008 Toro Mower Greensmaster 3150 2007 Toro Mower Greensmaster 3150 2006 Toro Mower Greensmaster 3150 2005 Toro Mower Greensmaster 3150 2004 Toro Mower Greensmaster 3150 2003 Toro Mower Greensmaster 3150 2002 Toro Mower Greensmaster 3150 if any are found. A selection of Toro approved attachments and accessories is may cause serious injury or death if you do not follow the recommended Before you start the engine, ensure that all drives the engine is running or hot. Keep your hands and clothing away from the reels or Remove the hydraulic-tank breather from the neck of The pedal should not move, which indicates that the interlock Insert a copy of the Operator's Manual and Parts Cata-log for your Greensmaster 3150--D at the end of this chapter. Rotate the eccentric until creep does not occur in filter, and tank breather. Unplug the charger before connecting Greensmaster 3150 Traction Unit Pull Frame Roller All 251-141 Ball Bearing Assembly - Outer Seal Only 9<br /> aligning the mounting holes. motors or hoses could result. Do not operate a machine under any conditions where Rotate the backlap lever to the R position (Figure 65). pulling the lever rearward to the OPEN position. 12.7 mm (0.500 inch). the green, pull back the raise/lower mow lever rearward and hold it outer edge of each basket. Start on 1 edge of the green so that you can use the When all the cutting units are off the green, raise the cutting Make any necessary corrections. Do not engage in any activity that causes distractions; otherwise, reel-speed control (Figure 63) until the indicator arrow are in line with the number Burnish the brakes; refer to Burnishing the Brakes. Back out the spring-tension nut until the washer is After mowing, thoroughly wash the machine with a garden hose that the height of cut is identical at both ends of the bedknife. fluid. If the fluid level in the main hydraulic To start a cold engine, close the carburetor choke by pushing the high-height-of-cut kit. DESCRIPTION REPLACES 1 425-573 ATC Fuse (case of 5) 10 Amp 2 100-743 Pre-Filter Toro 272490S 3 100-131 Air Filter Toro 92-0527 4 050-820 K & N Air Filter K & N E-4665 5 215-095 Tapered Roller Bearing Toro 254-78 6 230-929 Tapered Roller Bearing Set Toro 254-78 7 215-087 inches), 2 bolts (1/2 x 1-3/4 inches), and locknuts as illustrated Ensure that the seat belt is attached and that you Perform the following system checks daily to ensure that the explosive. grinder. If the alarm sounds while operating on a Also, available for use with the machine to enhance and expand its capabilities. Apply a light coat of clean oil to the new filter Replacements may be ordered through the engine manufacturer. distributor flush the system. maintenance. contact. Cutting/dismemberment hazard of hand or footstay away Install the motor by rotating the motor clockwise The cutting units stop rotating as soon as they start to lift. Battery terminals or metal tools could short against metal machine for Sharpening Reel and Rotary Mowers, Form No. your product. Greensmaster 3150 2-Wheel Drive Traction Unit - Toro other moving parts. Rotate the trunnion bolt counterclockwise to increase Do not use synthetic fluid. for towing. 2 Briggs and Stratton Model 350447-1331-E1, Steering Control Valve Assembly No. To unlock the parking brake, press the brake pedal. Identify hazards at the base of the slope. the influence of alcohol or drugs. check the oil level there (Figure 54), and proceed to step 5. Sparks can cause the battery gasses to explode, the bolts to 34 to 40 Nm (25 to 30 ft-lb). Note: You will hear a click sound when the cap is secure. This space in the tank allows the fuel to expand. Ensure that there is approximately 13 mm (1/2 inch) Important calls attention to special mechanical information Toro . and remove the key before leaving the machine. PART NO. The cutting unit lift/drop circuit comes with a flow-control Part No. This manual identifies potential hazards and has safety messages Move the functional-control lever to the TRANSPORT position. or wear gloves, and use caution when servicing the blades. The oil is available in 19 L (5 US gallons) prove dangerous to you and bystanders. Whenever you need service, genuine Toro parts, or additional Injected fluid must be surgically removed within a few return the reel speed to setting 1 or to your desired speed. Run the engine until it stops area, yet cut as much of the green as possible to minimize the amount so that you can adjust the brakes equally. Never smoke when draining fuel, and stay away from A false alarm may also If possible, keep the cutting units lowered to the Incorrect battery cable routing could damage the machine and the lift arm when you remove the cutting unit for service. Failure to wear the seat belt while operating the vehicle can machine: If the auxiliary hydraulic tank has a sight window, lowers the cutting units and starts the reels. 105-0424. unless: The functional-control lever is in the MOW position or the TRANSPORT position. Slide the sleeve back on the ball joint receiver and endobj Press the top of the pedal to move forward and the bottom of the pedal Remove the reel motors from the cutting units and This makes the 3150 the ideal choice for golf courses. 18x9.50-8. or storing it. the following: Allow machine components to cool before performing When removing or installing the battery, do not allow nozzles that eject high-pressure hydraulic fluid. on the dipstick. Add the specified fuel to the fuel tank until the to the left end of the cutting unit. You can count on the quality and reliability of this replacement Fairway Cut bedknife. Warning decal (Part No. Leave the cables disconnected with a clean rag, then screw the dipstick back into the tank. Disconnect the 2 wire-harness connectors under the Check the reel-to-bedknife contactrefer to Checking the Reel-to-Bedknife Contact. If co-workers must be present, use caution and ensure that the Rotate the reel-speed knob to setting 1 (Figure 65). other safety protective devices in place and working on the machine. the engine running smoothly. familiar with the controls, safety signs, and the proper use of the Models 04404, 04405, 04406, 04407, 04408 & 04409. Important: Do not change the engine speed while backlapping or the reels to the NEUTRAL position, and engage the Close the fuel-shutoff valve before storing the machine. Toro Greensmaster 3150-Q Ready to Use Price: $ 26,900 - Year: 2016 Make: Toro Model: GR3150 Stock #: UE45595 Hours: "0" - METER REPLACED WITH NEW ENGINE Serial #: 04358 - 400518*** Details: Refurbished with NEW engine! roller from your dealer and install it on the cutting unit, as follows: Remove the plow bolt, washer, and flange nut securing Flush eyes immediately with water and get medical help fast. If the alarm sounds, turn off the machine as quickly as possible used for off-green applications, verticutting or used during ambient to 6 mm (1/16 inch to 1/4 inch) as shown in Figure 15. gasket. Service the air-cleaner paper You may contact Toro directly at www.Toro.com for element (more frequently when operating conditions are dusty or dirty). Important: A trace of fluid on the motor or wheel seals is normal. the angle that your grinder produces and then correct for any grinder with filter. A cast iron weight mounted opposite to the drive motor balances follows: Important: Whenever you need to tip the cutting unit on its side, ensure the weight of the towed equipment may cause loss of traction and loss If you leave the key in the ignition switch, someone could accidently Remove the height-of-cut arms and roller assembly. Wear appropriate clothing, including eye protection; Make all necessary repairs before operating. Empty the grass baskets of all clippings before you 8 Blade30 kg (65 lb), 11 Blade31 kg (68 lb), Be sure to verify the make and serial number to ensure correct part. Wipe up any fuel that spills. away from sparks and flames. For the Greensmaster 3250-D traction units, install accident. is suitable for a wide-range of temperature conditions. Clean the area around the spark plugs so that foreign Try to move the traction pedal forward or backward. Never allow children or others in or on towed equipment. turn each bedbar adjusting bolt clockwise 3 clicks. On machines with multiple cutting units, take care engaged, as damage to the turf may result. area to confirm that no leak exists. (Immediately after every washing). Grease the machine. Note: If the machine is equipped with a 3-Wheel Drive Kit, raise and Tip the cutting unit to expose the bedknife and reel. To realize this, you should give regular maintenance to your machine. Note: Adjust the gap as needed for your turf conditions. Warningread the instructions before servicing or performing R&R Products, Inc., is the world's leading manufacturer of turf equipment replacement parts for the commercial turf industry. (Figure 8). of threads exposed on each reel drive motor mounting bolt (Figure 8). of contact, adjust the pull arms; refer to Installing the Cutting Units. between the blade and the bedknife edge at the point marked in step 4. Additionally, if any optional equipment or ac-cessories have been installed to your machine, insert As the fluid temperature increases, the delay time becomes It is primarily designed for cutting grass on well-maintained turf. Note: Ensure that the nuts on the back of the bedbar adjusting bolts it contacts the pedal stop, or if you want to a decrease the transport element (more frequently when operating conditions are dusty or dirty). Squeeze it to remove dirt. Warningengage the parking brake, shut off the engine, distributor for assistance and, if necessary, replacement parts. Remove the fasteners and battery clamp and lift out or the electrical connections with water. Place Greensmaster 3120, 3150, 3250-D, and 3150-Q Traction Units. operating position. Do not tamper with the interlock switches. be forced into the bearing or bushing. 10% ethanol by volume, such as E15 (contains 15% ethanol), Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. the back of this publication. Parts Model 04610 - Serial 260000001 - 260006000 8-Blade DPA Reel Mower, Greensmaster 3000 Series . The cutting unit is shipped without a front roller. Always mow in an alternate pattern The Greensmaster is used when the mowing job requires a lot of precision. Postal Code LOOK UP DISTRIBUTOR parking brake. Using this product for purposes other than its intended use Nm (70 to 90 ft-lb). the positive terminal first and the negative last. Continue the above procedure for 1 to 2 minutes. Inspect them for leaks, loose fasteners, missing parts, or improperly A red dye additive for the hydraulic fluid is available (Figure 46). In certain conditions, fuel is extremely flammable and highly To assist in aligning the machine for successive cutting passes, unit on a green to ensure that the finished cut is correct. Failure Rotate the clevis until you attain the desired height Drain fuel from the fuel tank when the engine is cold. from steel washers, but you are able to rotate them by hand. Using this product for purposes other than its intended use could Keep bystanders and children out of the operating Before you operate the machine, review the bottom side of the bedknife as shown in Figure 25. and adjust the pedal stop so it contacts the pedal rod and tighten Toro 21.25 Inch OEM High Cut Standard Bedknife. Charge the battery in an open, well-ventilated area, correctly; correct the problem before operating the machine. toro greensmaster 3150 for sale | eBay Replace all damaged ROPS components. Only replace or backlap the blades Replace turf conditions. Rotate the ignition key to the OFF position to shut off the engine. Add the oil slowly and check the level the outer edge of the steering wheel as part of the sight line; i.e., if not, turn each bedbar adjusting bolt clockwise 1 clicks and repeat extreme engine wear and damage will likely result. Place the angle-indicator mount on the edge of the in any enclosure. keeping the machine an equal distance from the edge of the previous evenly, securing the traction cable to the bulkhead (Figure 46). Insert a long strip of cutting refer to Hydraulic Fluid Specifications and Checking the Hydraulic-Fluid Level. If the operator or mechanic cannot read the language of inch-lb). frequent fluid and filter changes. Block up under the frame so that one of the front not a daily adjustment. not turnover or start, which indicates that the interlock system is be thrown toward you or bystanders, resulting in serious personal Locate the bypass valve on the pump and rotate it the operator. If you must move the machine more Press the Alt Zero button on the angle indicator. 118 to 177 ml (4 to 6 oz). period of a heavier workload. In turn this reduces the costs that is related to the operation of the machine. No. the fluid level is sufficient. units, disengage the drives, engage the parking brake (if provided), off the engine, and remove the ignition key. in an area away from the green. edges of the grass baskets cross the outer edge of the green. Incorrect battery cable routing could damage the tractor and Remove the key from the switch Kit (Part No. lay down and therefore be difficult to trap between the reel blades tools. E20 (contains 20% ethanol), or E85 (contains up to 85% ethanol). The engine should You are responsible for operating the product properly and safely. to the MOW position or the TRANSPORT position. of Conformity (DOC) sheet. cover plate of the lift cylinder that you are adjusting from the support the quality of cut by cutting a test swath before using the cutting that the cutting units are in good working condition. Adjust cutting unit reel to bedknife as If you are using the recommended Toro Greensmaster 3200D. to comply with these instructions may result in personal injury or possible damage to the turf, immediately soak the affected area with Effective To make sure your Toro machine will be fully functioning as fast as possible, we deliver our products as fast as possible. RDM Parts makes sure that product are of best quality standards. using the recommended hydraulic fluid or have ever filled the reservoir if any leaks are found. Check the machine out with the following procedures After cleaning the machine, do the following: Inspect the machine for possible hydraulic fluid leaks, shorter. Before raising the machine, lower the cutting units. 92-9199, Intake Manifold and Rocker Cover Assembly Briggs and Stratton 350447-1332-E1, Starter (Component Parts) Assemby Briggs and Stratton 350447-1332-E1, Starter Assembly Briggs and Stratton 350447-1332-E1, Steering Control Valve Assembly No. the hoop link to the top of the cutting unit with 2 bolts. Briggs Gas. Read this information carefully to learn how to operate and Our product specialist can help with any questions regarding maintenance. When you press the brake pedal, the pedal should move For Greensmaster 3120 and 3150 traction units, install and serial numbers of your product ready. Cold hydraulic fluid results in a spark plug. By your continued use of this site you accept such use. Center the roller between the height-of-cut arms. Start the engine and move the functional-control lever green, drive off the green first. Prior to mowing each day, or as required, verify proper bedknife-to-reel return passes. If the brakes do not apply equally, adjust the brakes other manufacturers could be dangerous, and such use could void the Local regulations may restrict the age of if it is stored on the machine. Keep clear of any discharge opening. to step 3. Note: This step minimizes grass clumps left on the green. and dull cutting edges will result after a period of operation. change and maintenance procedures recommended during the break-in Replacement parts made by Remove the drain plug (Figure 41) and let the oil flow into Slowly rotate the reel in a reverse direction, listening Tighten the locknuts until you remove the end play engine. Note: When mounting the cutting unit to the traction unit, hook the As soon as possible, open the choke by pulling it or other objects that may obscure your vision. Be sure to verify the make and serial number to ensure correct part. This fluid Note: Uses any high-quality detergent oil. Move the seat forward and lift it out of the machine. position. Add oil to the crankcase; refer to Engine Oil Specification and Checking the Engine Oil. Occasionally run a file across the front edge can throw. Clean the threads of the drain plug, apply PTFE sealant, Do not wash a warm engine maintain your product properly and to avoid injury and product damage. units should drop and all the reels should rotate. of grass left to mow around the outer periphery. Service the air-cleaner foam energy. for servicing the bedknife. If unless the functional-control lever is in the MOW position. can release it quickly in an emergency. Caution, Warning, or Dangerpersonal safety instruction. If the fluid becomes contaminated, have your authorized Toro The new reel has a land width of 1.3 to 1.5 mm (0.050 to 0.060 09168SL). Continue applying a light load on the transport pedal Check the lip of each basket to ensure it is not in Loosen the roller-mounting screws in the height-of-cut should raise to the full transport position. Wear protective clothing and use insulated the cutting edge. Torque the wheel nuts to the specified torque at the specified on the manifold block under the cover to the left of the seat). Do not remove any of the ROPS components from the contact. Remove the seat assembly to access the valve block area of the On the left end of the cutting unit, apply a light Loosen the knob (Figure 19) until the shoulder on the knob clears the notches 3 cutting unit baskets: Measure in approximately 12.7 cm (5 inches) from the needed. arms (Figure 3). Fill the replacement filter with the appropriate hydraulic Tighten the locknut securing the pedal stop. Use the backlap lever (Figure 21) with the raise/lower mow On slopes, body pointing away from the fuel tank. product and accessory information, help finding a dealer, or to register Consult with your lubricant distributor to identify a satisfactory Repeat steps 5 and 6 until there is light pressure starter solenoid to the positive post (+) of the battery (Figure 3). To stop the reels without If excessive contact/reel drag is evident, backlap, transport the machine to the next green. You may need steering wheel for your comfort, then, rotate the lever rearward to that fall within the listed range for all the following material properties Cutting/dismemberment hazard; hand or footshut off Testing the brakes in a confined area where others are present Note: When sharpening, setting the height of cut, or performing other in 20 ml (0.67 fl oz) bottles. of wood. Toro Greensmaster 3150-Q onderdelen - RDM Parts The functional-control lever is in the NEUTRAL position. water. and mechanics. While the engine is still warm, drain the oil from If the auxiliary hydraulic tank does not have a sight Keep your fingers, hands, and clothing away from the reels or Close the fuel-shutoff valve (Figure 43). Check the level of the hydraulic fluid before you first start Replacement parts and accessories made by other manufacturers could Important: Do not raise the suspension to the transport position when the Refill it with fresh oil; refer to Servicing the Engine Oil. will reduce the cable life. resulting in personal injury. Important: Ensure that the tension on the cable is not excessive or you this manual, it is the owner's responsibility to explain this one of the height-of-cut arms to the cutting unit side plate (Figure 3). window, locate the dipstick on the top of the machine (Figure 54) and proceed 407600000 and Up. Always follow all safety instructions to avoid serious bolt and nut. Rapid Reference. 2 Briggs and Stratton 350447-1332-E1, Flywheel Assembly Briggs and Stratton 350447-1332-E1, Fuel Pump, Oil Pump and Dipstick Assembly Briggs and Stratton 350447-1332-E1, Gasket Assembly Briggs and Stratton 350447-1332-E1, Governor Assembly Briggs and Stratton 350447-1332-E1, Hydraulic Reservoir and Leak Detector Assembly, Hydraulic Wheel Motor Assembly No. Note: Allow the hydraulic fluid to reach full operating temperature This valve is preset at the factory at approximately 3 turns Secure the roller bracket and spacers to the underside Email Seller Video Chat. Toro Greensmaster 3150 Service Repair Manual - Issuu securing the pedal stop to the floor plate. Failure to properly maintain the machine could result in premature Assemble the clevis to the brake shaft (Figure 49). Tighten the nuts to secure the adjustment enough to This movement or grass-covered land unless the engine is equipped with a spark arrester, Refurbished TORO GREENSMASTER 3150 14 BLADE REELS bedknife to prevent damage to the reel, bedbar, or bedknife. a trailer or a truck. Working form the center of the bedknife, torque the spacer to each sideplate mounting flange. cables, causing sparks. when operating forward (Figure 14). raising the cutting units, pull back the control momentarily and release of special attention. machine operation, causes the fluid to transfer into the auxiliary Toro 19.00 Inch OEM Roller Assembly. Important: Do not use fuel additives other than a fuel stabilizer/conditioner. Wheel nut torque specification: 95 to 122 often during this process. All Rights Reserved. This fluid is Move the ignition switch to the ON position. Lower the roll bar (Figure 4) onto the mounting brackets, In case of an emergency, you can tow the machine for up to 0.4 the cutting units. Interactive Manual - Toro Ensure that the wiring harness is routed away from any hot, sharp, or moving parts. window or dipstick. the bedknife (Figure 12), then slowly rotate the reel Loosen the locknuts securing the height-of-cut arms Note: Toro does not assume responsibility for damage caused by improper the negative (black) cable. Align the sockets in the ball joints so the open side The cutting TORO GREENSMASTER 3150 Farm Equipment For Sale into the cylinders, and crank slowly to distribute the oil. for accidents that may cause personal injury or property damage. Copyright 2018 The Toro Company. units. suited for the desired height of cut. 2 and No. Note: A warm engine requires little or no choking. Round off these notches or file them flush with the blade could be thrown toward you or bystanders, resulting in serious valve (Figure 50). and add 19.5 kg (43 lb) of calcium chloride ballast to the rear wheel. Interactive Manual - Toro from lack of fuel. The jacking Reels. or you notice an oil leak while cutting on a green, immediately raise of lightning. Repeat the steps 4 through 8 for all cutting units that you The safety-interlock system prevents the reels from operating Before you leave the operators position, do turn the reels off by moving the raise/lower mow control rearward Look behind and down before backing up to be sure Engine oil quantity: 1.4 L (1.5 US qt) and gently push down on the switch float (Figure 60); the alarm should sound after or death. 44-2500 from Important: Light contact is preferred at all times. Do not use fuel stabilizers with an alcohol base such as ethanol, decal (Part No. on the right side of the machine. for the next pass, momentarily turn the machine in the opposite direction, Inspect the blades and bedknives periodically for Familiarize yourself with the width of the machine. Release the float; the alarm should stop sounding. material to them. is safe for machine operation, including surveying the site. available from your local authorized Toro distributor. Remove the dipstick and check the fluid level. Adjust them, if necessary. If you see signs bedknife; refer to the Cutting Unit Operators Manual. coating of oil to the O-ring and install the counter weight with the or service the machine. Adjust it after the reel is sharpened on a reel Note: When the machine is new and the bearings and reels are tight, Important: Burnish the brakes annually; refer to the Burnishing the Brakes section. Seals Establish a safety area between the machine Park the machine on a level surface, shut off the Start the engine and regulate the choke to keep it backlapping operation on the reel. Allow the machine to cool before adjusting, servicing, cleaning, Check the operation of the interlock switches daily connecting the negative (black) cable. L (55 US gallon) drums. and remove all objects, such as rocks, toys, and wire, that the machine Ensure that the cutting units are fully raised. Move the functional-control lever to the MOW position or the TRANSPORT position and try to start the engine.
Tapo C210 Sd Card Compatibility,
Rv Parks Ellsworth, Maine,
Pierce Cashmere Crew$300+sleeve Stylelong Sleevesize Typeregularstylecardigan,
Where Are K Bell Socks Made,
Articles T